New Research In
Physical Sciences
Social Sciences
Featured Portals
Articles by Topic
Biological Sciences
Featured Portals
Articles by Topic
 Agricultural Sciences
 Anthropology
 Applied Biological Sciences
 Biochemistry
 Biophysics and Computational Biology
 Cell Biology
 Developmental Biology
 Ecology
 Environmental Sciences
 Evolution
 Genetics
 Immunology and Inflammation
 Medical Sciences
 Microbiology
 Neuroscience
 Pharmacology
 Physiology
 Plant Biology
 Population Biology
 Psychological and Cognitive Sciences
 Sustainability Science
 Systems Biology
Scaling theory for quasibrittle structural failure

Contributed by Zdeněk P. Bažant, June 8, 2004
Abstract
This inaugural article has a twofold purpose: (i) to present a simpler and more general justification of the fundamental scaling laws of quasibrittle fracture, bridging the asymptotic behaviors of plasticity, linear elastic fracture mechanics, and Weibull statistical theory of brittle failure, and (ii) to give a broad but succinct overview of various applications and ramifications covering many fields, many kinds of quasibrittle materials, and many scales (from 10^{–8} to 10^{6} m). The justification rests on developing a method to combine dimensional analysis of cohesive fracture with secondorder accurate asymptotic matching. This method exploits the recently established general asymptotic properties of the cohesive crack model and nonlocal Weibull statistical model. The key idea is to select the dimensionless variables in such a way that, in each asymptotic case, all of them vanish except one. The minimal nature of the hypotheses made explains the surprisingly broad applicability of the scaling laws.
Discovery of the concept of stress and strength by Galileo (1) may, in retrospect, be regarded as the first scaling theory of solid mechanics. This theory, now known to apply only to elastoplastic behavior, captures the fact that, under controlled load P, geometrically similar structures of different sizes D fail at the same nominal stress σ _{N} , defined as the maximum stress in the structure (if no stress singularities exist) or simply as σ _{N} = P/D ^{2} or P/bD for three or twodimensional scaling (b = structure thickness). Any departure from such scaling came to be known as the “size effect.”
About 350 years ago, Mariotte (2) pointed out that a size effect must arise because the local material strength is random and its minimum encountered in a structure decreases with D. Nevertheless, proper mathematical formulation of this idea had to wait until 1939. That year, Weibull (3) experimentally demonstrated that σ _{N} for brittle structures has the probability distribution that came to bear his name, although already in 1928 this distribution was derived by Fischer and Tippett (4) as the only possible limiting distribution with a threshold for the minimum of a set of n independent random variables for n → ∞. The tail of this distribution is a power law, from which Weibull deduced that the statistical size effect is also a power law, the exponent of which is a function of the coefficient of variation ω of material strength.
For half a century afterward, whenever a size effect was observed, it was generally attributed to Weibull theory (3, 5, 6), which was amply confirmed for fatigued metals and finegrained ceramics. However, beginning with studies of concrete for nuclear reactors during 1970–1985, it gradually transpired that Weibull theory does not apply to materials now termed “quasibrittle” (7–9). These are materials in which the fracture process zone (FPZ) is not negligible compared with the crosssection dimension D (and may even encompass the entire cross section).
Depending on the scale of observation or application, quasibrittle materials include concrete, fiber composites, toughened ceramics, rigid foams, nanocomposites, sea ice, consolidated snow, rocks, mortar, masonry, fiberreinforced concretes, stiff clays, silts, grouted soils, cemented sands, wood, paper, particle board, filled elastomers, various refractories, coal, dental cements, bone, cartilage, biological shells, cast iron, and modern tough alloys. In these materials, the FPZ (the length of which is usually 5–50 times the dominant material inhomogeneity size) undergoes softening damage such as microcracking; it represents almost the entire nonlinear zone at the crack tip, and the transverse stress declines gradually along the FPZ length (9–13). In ductile fracture of metals, by contrast, the FPZ is essentially a point within a large nonlinear zone undergoing plastic yielding rather than damage. The FPZ length can vary enormously; it is typically ≈50 cm in normal concretes, 5 cm in highstrength concretes, 10 μm to 1 mm in finegrained ceramics, 10 nm in a silicon wafer, 100 m in a mountain mass intersected by rock joints, 1–10 m in an Arctic sea ice floe, and ≈20 km in the ice cover of Arctic Ocean (consisting of thick floes a few kilometers in size, connected by thin ice). If the FPZ is negligible compared with D, a quasibrittle material becomes perfectly brittle, i.e., follows linear elastic fracture mechanics (LEFM). Thus, concrete is quasibrittle on the scale of normal beams and columns but perfectly brittle on the scale of a dam. Arctic Ocean cover, finegrained ceramic, or nanocomposite are quasibrittle on the scale of 10 km, 0.1 mm, or 0.1 μm but brittle on the scale of 1,000 km, 1 cm, or 10 μm, respectively.
Scaling Laws and Their Asymptotic Support
Asymptotics of Energetic Size Effect. First, let us show an elementary explanation of the nonstatistical size effect in a very specific situation (14). Consider rectangular panels of different sizes under initially uniform uniaxial tension σ _{N} (Fig. 1a ) and assume that their failure modes are similar, which means that a _{0}/D = constant at maximum load P _{max} (a _{0} = crack length excluding the FPZ). Formation of a crack relieves the stress, and thus releases strain energy, approximately from the shaded triangles on the crack flanks, limited by lines of some slope k emanating from the middle of the FPZ. To determine k, one would need to solve the boundary value problem of elasticity, but for us it suffices to know that k is constant for similar panels of different sizes D. The potential energy (ends being fixed) is where Π_{0} = constant and A_{r} = area of the triangles = ka ^{2} (a = a _{0} + c_{f} ≈ equivalent crack length, c_{f} = constant ≈ half length of the FPZ; Fig. 1a ). The supports being fixed, the fracture can grow if the rate of energy release, –∂Π/∂a, is equal to the energy dissipation rate bG_{f} (G_{f} = fracture energy of material). Solving σ _{N} from this condition, one obtains the classical energetic size effect law for failures with large cracks or notches (14) (Fig. 1 e and j–p ): D _{0} = c_{f} (D/a _{0}) and σ_{0} = (EG_{f} /kc_{f} )^{1/2} are constants (independent of D). The sizeeffect law in Eq. 1 applies to many geometries. It was verified experimentally and justified theoretically for a surprisingly broad range of many different materials and structures (9, 12–23). The law was derived by asymptotic approximations of equivalent LEFM (9, 15, 18, 24), of the cohesive crack model (9, 12) and of Jintegral (25) and was verified by numerical simulations with the crack band model, nonlocaldamage model, and various types of randomparticle or lattice models. Another nonstatistical scaling law of broad applicability was later found for failures at crack initiation (9, 12, 13, 17, 26–32).
It will now be shown that both scaling laws follow logically from the general asymptotic properties of quasibrittle fracture if one exploits the asymptotic matching philosophy well known from fluid mechanics (33–36). Although the asymptotic matching properties of the sizeeffect laws were recently highlighted (12, 13, 37–39), a systematic matching procedure was not used and will be presented here.
As a compromise between reality and simplicity, quasibrittle fracture may be described by the cohesive (or fictitious) crack model, originated by Barenblatt (40) and extended by others (9, 41–44). The FPZ at the crack front (Fig. 1 a, e, and o ) is modeled as a fictitious line crack transmitting cohesive (crackbridging) stresses σ = f_{t} ϕ(w̄); w̄ = wf_{t} /G_{f} = dimensionless opening; w = crack opening (separation); f_{t} = tensile strength of material; ϕ(w̄) = monotonically decreasing (softening) function (Fig. 1c ), assumed to have a finite initial slope; = area under the initial tangent of σ (w)curve (Fig. 1c ); G_{f} is called the initial fracture energy, to be distinguished from the usual fracture energy = total area under the complete σ(w)curve (Fig. 1c ) = critical energy flux into the FPZ in infinite body (41). By definition, ϕ(0) = 1 and ϕ′(0) = –1/2.
Depending on the first two nonzero terms of the asymptotic expansions in powers of D and D ^{–1}, there exist three and only three types of size effect (12, 13, 37): where b _{0}, c _{0},..., c _{3} are positive constants determined by structure geometry (sections 2.12 and 9.4 and equations 9.61, 9.39, and 9.73 in ref. 12). Type 1 (Fig. 1d ) occurs if the geometry is such that P _{max} is reached at crack initiation from the FPZ at a smooth surface, i.e., as soon as the FPZ is fully formed; type 2 (Fig. 1e ) occurs if there is a large notch or preexisting stressfree (fatigued) crack and if the geometry is positive (12), i.e., such that P _{max} occurs while the FPZ is still attached to the tip; and type 3 occurs if a large crack can grow stably prior to P _{max} [negative geometry (12)]. The sizeeffect types 1 and 2 are very different, but types 2 and 3 are quite similar and hardly distinguishable in fracture testing (Fig. 1e ). Eq. 2 was derived by perturbation analysis of the elastic boundary value problem (12, 13, 37). Eqs. 3–5 were derived from equivalent LEFM and verified by asymptotic expansions based on the smearedtip method (12, 13, 15, 45).
The first terms in Eqs. 2–5 represent powerlaw scaling. Transition from one power law to another is normally handled by renormalization group transformation (34). This transformation, however, merely identifies the intersection of adjacent power laws, relating one power law to another. It does not describe the gradual transition between them, which can be very broad, often spanning 3 or 4 orders of magnitude. Thus, the second asymptotic terms are important, too.
Asymptotics of EnergeticStatistical Size Effect. In Weibull theory, the failure probability at a continuum point is assumed to be a function of the stress at that point. However, for heterogeneous (quasibrittle) materials, one must introduce a nonlocal generalization in which it is assumed that the probability of failure at a given point of the macroscopic smoothing continuum is a function of the average strain in a certain neighborhood of that point, the size of which is a material property (46). This hypothesis, which was shown to give good agreement with experimental observations (29–32), has the nonlocal damage model as its deterministic limit and permits dealing with failures occurring not only at crack initiation (type 1) but also after large crack growth (types 2 and 3). Numerical simulations as well as asymptotic approximations of nonlocal Weibull theory (46) have shown that, in quasibrittle failures, material randomness does not appreciably affect the mean energetic size effect except for large structures failing at crack initiation. Therefore, the asymptotic properties in Eqs. 2–5 apply to the mean σ _{N} , except that Eq. 3 for asymptotic type 1 size effect must be modified: Here m = Weibull modulus and n = number of dimensions in which the structure is scaled (n = 1, 2, 3); typically, m = 10–40 and n/m « 1. Eq. 6 means, not surprisingly, that Weibull size effect must apply for failures at crack initiation if the FPZ is negligible compared with D.
Asymptotic Matching Law for Type 2 or 3 Scaling. The general approximate sizeeffect law can be derived by combining dimensional analysis with asymptotic matching. From the Πtheorem of dimensional analysis (33, 34), two special size effects can be readily proven: (i) if the failure depends on f_{t} (dimension N/m^{2}) but not G_{f} , then there is no size effect, i.e., σ _{N} = constant (this is so for all elastoplastic failures); (ii) if the failure depends on G_{f} (dimension J/m^{2}) but not on f_{t} , then there is a size effect of the type σ _{N} ∝ D ^{–1/2} (this is so for LEFM if the cracks or notches are geometrically similar). Nothing more can be deduced from dimensional analysis alone.
One can, however, deduce more information after considering the physical meaning of the material characteristic length governing the FPZ size, (47). The FPZ length and width for D → ∞ are ηℓ and η′ℓ where η and η′ are constants of the order of 1 depending on microstructure characteristics (the parameter l_{e} = G_{f} /E is also a length but is irrelevant for failure because it controls the ratio of deformation to stress intensity factor K_{I} in LEFM). Depending on the ratio D/ℓ, two asymptotic cases may be distinguished (Fig. 1 e and j–p ). (i) When D/ℓ → 0, the body is much smaller than a fully developed FPZ. Thus, G_{f} cannot matter. Therefore, the case of no size effect, σ _{N} = constant, is the smallsize asymptote. (ii) When D/ℓ → ∞, the FPZ becomes a point in dimensionless coordinates and the stress field approaches a singularity. Thus, f_{t} cannot matter. Therefore, the LEFM scaling, σ _{N} ∝ D ^{–1/2}, is the largesize asymptote of quasibrittle failure [which is represented by a straight line of slope –1/2 in the plot of log σ _{N} versus log D (Fig. 1 e and j–p )]. For the intermediate sizes, the sizeeffect curve may be expected to be a gradual transition between these two asymptotes. It will now be shown that the approximate form of this transition can be deduced after noting how the asymptotes are approached, i.e., by exploiting the higherorder asymptotic terms in Eqs. 2 and 4.
Examining the formulation of the boundary value problem with cohesive crack to dimensionless variables, one concludes that [if the structure shape, a _{0}/D and curve ϕ(w̄) are fixed] σ _{N} depends on only three parameters, f_{t}, D and K_{c} , where K_{c} = (EG_{f} )^{1/2} = mode I fracture toughness for plane strain, E = Young's modulus [for plane stress, E needs to be everywhere in this article replaced by E′ = E/(1 – ν^{2}); ν = Poisson ratio]. Thus, there are four governing parameters, σ _{N}, D, f_{t} , and K_{c} . Because they involve two independent physical dimensions (length and force), the Πtheorem (33, 34) implies that there can be only 4 – 2, i.e., two independent dimensionless parameters, Π_{1} and Π_{2}.
So, the equation governing failure may be written as F(Π_{1}, Π_{2}) = 0, where function F is assumed to be sufficiently smooth. Although many diverse choices of Π _{i} (i = 1, 2) are possible, the key idea proposed here is to make a choice for which, in each asymptotic case, all Π _{i} vanish except one. If consideration is limited to dimensionless monomials, this can be most generally achieved by choosing where p, q, u, and v are four unknown real constants. Indeed, if we let Π_{1} = 0 correspond to D → 0, then F(0, Π_{2}) = 0, which implies that Π_{2} = constant or for D → 0, which must be the case of no size effect; hence, v = 0. If we let Π_{2} = 0 correspond to D → ∞, then F(Π_{1}, 0) = 0, which implies that Π_{1} = constant or , or σ _{N} ∝ D ^{–} u/p for D → ∞, which must be the LEFM scaling; hence, u/p = 1/2 or u = p/2. To find p and q, we truncate the Taylor series expansion of F after the linear terms: where F _{1} = [∂F/∂Π_{1}]_{0} and F _{2} = [∂F/∂Π_{2}]_{0} (evaluated at Π_{1} = Π_{2} = 0) and F _{0} = F(0, 0) (F _{0}, F _{1}, F _{2} ≠ 0). For general p and q, the last equation cannot be solved explicitly for σ _{N} , but it can for D: This may be compared with the inverse of the largesize asymptotic expansion (Eq. 4), which has the form for σ _{N} → 0 (B _{2}, C _{2} = positive constants). Evidently, matching of the first two terms of this expansion requires p = q = 2. Then, Eq. 9 can be solved for σ _{N} . This yields, and verifies, the sizeeffect law (Eq. 1) (Fig. 1 e and j–p ) in which σ_{0} = f_{t} (–F _{0} F _{2})^{–1/2} and D _{0} = ℓF _{2}/F _{1}. For D → 0, Eq. 1 has the approximation which verifies that the form of the second term of smallsize expansion (Eq. 2) can be matched, too. Thus, Eq. 1 is the simplest formula for type 2 size effect that can match four asymptotic terms, two for D → 0 and two for D → ∞. [However, if not only the form of the secondorder terms but also the values of all four coefficients b _{0}, c _{0}, b _{2}, and c _{2} are given, a slightly more general formula with four adjustable parameters is needed (48).]
More complex formulas of the same asymptotic accuracy, but more flexible in data fitting, can be obtained by replacing Eq. 7 with dimensionless polynomials (or other monotonic functions of Π_{1} and Π_{2}). Such formulas can make a significant difference only if the size effect needs to be modeled for a size range exceeding ≈1½ orders of magnitude of D. Their merit is that they can capture a spectrum of fracture energies (12, 49), each of which is associated with a different order of magnitude of D.
The type 3 sizeeffect formula ensues similarly. The result is where σ_{0}, D _{0}, and χ = constants (Fig. 1e ). To ensure monotonicity, χ ≥ 1 (12, 37).
Asymptotic Matching Law for Type 1 Scaling. Failures at macrocrack initiation from a smooth surface need a somewhat different approach. They can be treated as a limit case of finite crack for a _{0} → 0 (12, 15, 28), but because the energy release rate at crack initiation is zero, it is easier to analyze the stress redistribution caused by a finite FPZ that releases energy and must occur before a macrocrack can initiate. The nonstatistical type 1 size effect (also called, albeit not quite accurately, the straingradient effect) can be instructively explained by the flexural test of a beam (Fig. 1 b and q ) (26). G_{f} is here irrelevant for P _{max}, and what matters is the thickness, λℓ, of the boundary layer of cracking (λ being a constant of the order of 1, depending on microstructure properties). P _{max} occurs roughly when the average of the elastically calculated flexural stress σ over the thickness of the boundary layer equals f_{t} , i.e., when k_{M}Mc/I = f_{t} , in which I = bh ^{3}/12, c = D/2 – λℓ/2, M = k_{M}L(σ _{N}bD) = bending moment, L = beam span, and k_{M} = constant for geometrically similar beams. Solution yields , where ξ = λℓ/D and (26). This approximation is secondorder accurate for ξ « 1 or D » ℓ but unacceptable for smaller D because it jumps to negative σ _{N} . To get acceptable approximation of the same secondorder accuracy in D ^{–1}, set (1 – ξ)^{–1} ≈ (1 + rξ)^{1/} r (r = constant ≠ 0); this gives the deterministic type 1 size effect (Fig. 1d ):
For general dimensional analysis, we need a slightly different procedure than for type 2. Consider the deterministic type 1 first (m → ∞). Because, according to Eqs. 2 and 3, both asymptotes in the plot of log σ _{N} vs. log D are horizontal, the curve in Fig. 1d must have an inflexion point. This postulating suggests the existence of what is called an “intermediate asymptote” (34), which consists of some unknown power law. Because it separates the largesize and smallsize asymptotics, we now try to match the largesize asymptotic terms alone and choose the largesize asymptote to correspond to Π_{1} = 0, i.e., to F(0, Π_{2}) = 0. This means that Π_{2} = constant for D → ∞, and thus v = 0 in Eq. 7. The linear approximation (Eq. 8) cannot in general be solved for σ _{N} , but it can for D: The largesize expansion may be generalized as σ _{N} = (b _{1} + rc _{1} D ^{–1} +...)^{1/} r, without contradicting Eq. 3 (r = arbitrary constant ≠ 0). The inverse expansion is 1/D = (–b _{1} + σ ^{r} +...)/rc _{1}, and matching of Eq. 15 obviously requires u =–1 and p = q = –r in Eq. 7. So Π_{1} = (f_{t} /σ _{N} ) ^{r} ℓ/D and Π_{2} = (f_{t} /σ _{N} ) ^{r} . Now Eq. 8 can be solved for σ _{N} . This yields, and thus verifies, Eq. 14, in which λ = F _{1}/rF _{2} and .
For the statistical case (m < ∞), we again choose the largesize asymptote to correspond to Π_{1} = 0, Π_{2} = constant. To match Eq. 6, σ _{N} = C _{1} D ^{–n/m} ∝ f_{t} (D/ℓ)^{–} v/q; thus, v/q = n/m. Not to loose the deterministic limit, we keep p = q = –r and u = –1. Eq. 8 can now be solved for σ _{N} , which leads to the mean type 1 energeticstatistical size effect (Fig. 1 d and q ), where , κ = λ ^{rn/m–1}F _{1}/F _{2} r, and r is a parameter of the order of 1, sensitive to structure geometry.
Eq. 16, however, violates the smallsize asymptotics in Eq. 2, and therefore must be modified further, but without affecting the first two largesize asymptotic terms. To bridge the smallsize and intermediate asymptotes, we could engage in similar arguments as we did for bridging the largesize and intermediate asymptotes. Suffice to say, the complete law for the meansize effect of type 1 (Fig. 1d ), matching the smallsize asymptotics in Eq. 2, is obtained by replacing λℓ/D in Eq. 16 with θ (39): where η = positive constant of the order of 1 and s may be taken as 1. Note that if we let η « D/ℓ « λ, or λ/η → ∞, Eq. 17 converges to the intermediate asymptote, which is given by the power law σ _{N} = s _{0}(κrη_{0}ℓ)^{1/r} D ^{–1/r} and coincides with the smallsize asymptote of Eq. 16 as well as with the largesize asymptote of . The physical reason for the existence of an intermediate asymptote is that normally the size of averaging domain in nonlocal Weibull theory (approximately the FPZ width) is much smaller than the FPZ length (39). Eq. 17 is supported by finite element simulations with nonlocal Weibull theory as well as test data from 10 different labs [all combined in one dimensionless plot in Fig. 1q (29–31)]. However, test data for concrete and composites show that the D values for which the difference between Eqs. 16 and 17 is significant are less than the material inhomogeneities, which means that Eq. 16 should mostly suffice in practice.
For bending of laminates or unreinforced concrete beams, the Weibull statistical component in Eq. 16 or 17 is usually insignificant for normal sizes (30, 50). It becomes significant only for bending fracture of very large structures such as arch dams.
Bridging of LEFM and Plasticity. To identify the sizeeffect parameters, one needs to anchor them to LEFM for D → ∞ and to plasticity for D → 0. In LEFM, the dimensionless energy release function g(α) characterizes the effect of structure geometry; it is defined as g(α) = k ^{2}(α), where α = a/D = relative length of crack or notch and . The tip α of an equivalent LEFM crack is placed into the middle of the FPZ, and the LEFM relation σ _{N} = [EG_{f} /Dg(α)]^{1/2} is expanded into Taylor series in θ = α – α_{0} = c_{f} /D about the initial relative length α_{0} of crack or notch, which is assumed to be the same for different D. Depending on which terms of this series vanish (first, second, or neither), and making sure that σ _{N} for D → 0 is finite (as required by plasticity), one obtains type 1 and 2 sizeeffect Eqs. 1 and 17. However, their parameters are now expressed in terms of g(α), which introduces the effect of structure geometry [similar formulas ensue more rigorously by the smearedtip method, in which a cohesive crack is regarded as a superposition of infinitely many LEFM cracks with continuously distributed tips and infinitely small K_{I} (12)]. For type 2, the relation σ _{N} = [EG_{f} /Dg(α)]^{1/2} with g(α) ≈ g(α_{0}) + g′(α_{0})c_{f} /D yields Eq. 1 with where ≈ half of FPZ length at P _{max} (ref. 48, Eq. 13) (c_{f} depends on geometry but not on D); and β = D/D _{0} = (D/c_{f} )g(α_{0})/g′(α_{0}) = B ^{2} g(α_{0})(D/ℓ) is called the brittleness number, because it characterizes proximity to the brittle behavior of LEFM, even for different geometries (18, 51); B is a geometry parameter of the order of 1, computed as if the crack were filled with a plastic “glue” (48).
Type 2 size effect has also been described in terms of equivalent , evaluated from tests as if c_{f} were 0, using LEFM; from Eq. 1 we have (18, 51).
Eq. 16 for type 1 size effect (typical of flexure of unnotched unreinforced beams) can be obtained as the limit case of equivalent LEFM when α_{0} → 0. Because g(0) = 0, one has . If (as usual) g″(0) < 0, the secondorder approximation leads to Eq. 16, in which , (12, 28).
Universal SizeEffect Law. The sizeeffect that bridges types 1 and 2 (i.e., for short notches or short cracks comprised within the boundary layer) is more complex. Using similar asymptotic matching procedures, one can construct the universal sizeeffect law (17). Fig. 1r shows a plot of its formula (38) matching all the seven asymptotic terms in Eqs. 2 and 4, and in Eq. 6 for the statistical case (with finite m).
Scaling of Probability Density Distribution of Failure Load. Structures must typically be designed for failure probabilities p_{f} of the order of 10^{–7}. Such a low probability can be assessed only theoretically, taking into account the size effect on the probability density function (pdf) of σ _{N} , based on the nonlocal Weibull theory (39). For D → 0, failure is nonpropagating and must occur nearly simultaneously along the entire failure surface. Thus, the pdf of σ _{N} must be Gaussian (except in faroff tails), as deduced from Daniels' fiber bundle model (52) (Fig. 1f Upper Left). With increasing D, the asymptotic size effect on the mean strength is nil, and the coefficient of variation (CoV) asymptotically decreases as D ^{–1/2}. For D → ∞, the pdf must be Weibull, corresponding to the weakestlink chain model (Fig. 1f Right), which implies a sizeindependent CoV. The gradual transition of pdf from Gaussian to Weibull, exemplified by various loadsharing models (53, 54), can be obtained by asymptotic matching (39) and calibrated by a chainofbundles model (Fig. 1f Center) (31).
Scaling for Interacting Fractures. Some failures require several fractures to form at different places. For example, statically indeterminate reinforced concrete beams or frames will collapse only after several critical cross sections (Fig. 1 h and i ) develop fractures due to bending (either at the tensioned face or, if reinforced for tension, at the compressed face). For not too large D, the cohesive fractures in different cross sections develop simultaneously (Fig. 1h ), causing a complex size effect. For D → 0, the behavior tends to be quasiplastic (Fig. 1g ) with no size effect. For large enough D, the fractures occur in sequence (note the spikes in Fig. 1i ), and then only one of them governs P _{max} (12, 13).
Some Generalizations. In compression fracture, e.g., kink bands in fiber composites, the softening curve of σ versus w may terminate with a finite residual stress σ _{R} . In that case, Eq. 1 must be replaced by (k_{r} = constant), which can be deduced from the Jintegral (25). G_{f} now represents the area between curve σ(w) and line σ = σ _{R} . Eqs. 2–5 and 7–12 remain valid if σ _{N} is replaced by σ _{N} – k_{r} σ _{R} .
Shear fracture of mode II or III can be analyzed similarly, with G_{f} replaced by the shear fracture energy.
Conspectus of Applications and Ramifications
Now that the general theory has been expounded, various applications and ramification will be reviewed succinctly. There is no room for complete references; they are found in refs. 9, 12, and 13.
Standards for Material Fracture Testing. Expressing the size effect in Eq. 1 with 18 by means of function g(α) brings about the advantage that, by measuring the maximum loads for nottoosmall notched specimens of different sizes (and possibly also different geometries), one can identify the mean and CoV of G_{f}, c_{f} , and ℓ (9, 12, 18, 24, 51) [this became a standardized testing method (55)]. The data fitting can be reduced to linear regression with slope 1/G_{f} and intercept c_{f} . The G_{f} thus obtained is the socalled initial fracture energy (48) (Fig. 1c ) (roughly, G_{f} ≈ 0.4 G_{F} for concrete, although the scatter is large). The reason why the sizeeffect method yields G_{f} rather than G_{F} is that the cohesive stresses σ at P _{max} are everywhere in the FPZ of test specimens (as well as nottoolarge structures) on the initial tangent (and not on the long tail, Fig. 1c ) of the softening curve, exceeding f_{t} /3 everywhere (48, 56, 57) (which explains why G_{f} , rather than G_{F} , must be used in Eqs. 7–13).
Recent work led to a more convenient (zerobrittleness) version of the sizeeffect method of G_{f} testing (48), in which it suffices to measure the maximum loads of only one notched specimen of a small size and one small unnotched specimen [except for statistics, this method is equivalent to the measurement of initial slope (57)]. The unnotched specimen permits determining the zerosize limit σ_{0} (27) of notched specimen strength, because for D → 0, failure is independent of G_{f} . For D → 0, the sizeeffect method based on equivalent LEFM requires a certain geometrydependent correction, given by parameter B defined below Eq. 18 and computed from the cohesive crack model (48).
Measuring the type 2 size effect, one can also deduce the resistance curve (R curve), describing how the apparent fracture energy (determined as in LEFM) varies with the crack extension from a notch. The R curve is the envelope of the family of fracture equilibrium curves for various D, and using this property one can derive from Eq. 1 an expression for the R curve (9, 18, 24).
Compression Fracture and Concrete Columns. Compression failure of concrete and other particulate composites is normally caused by a band of compression splitting cracks, propagating either in the direction of compression or inclined to it. The former is preferred (because extension of the existing axial microcracks requires less energy than formation of new ones). However (similar to Fig. 1a ), the inclined transverse propagation causes an asymptotically quadratic increase of energy release with fracture growth, whereas the axial propagation causes a linear increase. Therefore, the former must cause size effect, and the latter must not. So, there must exist a certain critical structure size above which the size effect will favor the inclined propagation. This behavior explains the size effect observed in concrete columns (9, 12, 13, 58) and large compression test specimens (59). The strain energy, and thus the size effect, is greater as the concrete columns are made more slender.
Stable growth of a tensile crack may provoke fracture under compressive stresses parallel to the tensile crack. This is so, e.g., for diagonal shear failure of reinforced concrete beams (60) (in which the size effect is due to compression fracture) and partly for compression punching of concrete slabs. However, for a dipping crack in gravity dam, running in compression direction, failure is caused not by compression but by a flexural crack branch through the ligament. Thus, compression fracture displays a rich palette of largecrack size effects.
Sea Ice Fracture. Size effects in sea ice have long been denied, because normalsize tests could not verify them. In retrospect, the reason was that brine voids, channels and pockets, thermal cracks, bottom roughness, and snow drifts cause the characteristic length of sea ice to be quite large: ℓ ≈ 2–10 m for horizontal and ≈0.5 m for vertical propagation of fracture (12, 25, 61). However, recent Arctic Ocean field tests of floating notched ice specimens of sizes up to 80 × 80 × 1.8 m, organized by Dempsey et al. (22), have established that, on the large scale, Eq. 1 is indeed followed, as predicted by both analytical and numerical studies of vertical penetration and of forces exerted against obstacles by moving ice (61). Eq. 1 explains why the forces measured on oil platforms are ≈1.5 orders of magnitude less than predicted by standard elastoplastic software.
Long cracks in the Arctic Ocean cover tend to run straight through thick ice floes rather than circuitously through thin ice between them. To explain this curious observation, it was shown (62) that the temperature drop ΔT needed to cause horizontal propagation of long flexural cooling cracks over the Arctic Ocean exhibits anomalous asymptotic scaling ΔT ∝ D ^{–3/8} rather than D ^{–1/2} (D = ice thickness). The reason is that the characteristic flexural wavelength L of a floating plate is proportional to D ^{3/4} rather than D, which means that ΔT ∝ L ^{–1/2}, and D needs to be replaced by L in Eq. 1.
Failure of Fiber Composites. Similar to concrete or ice, this is another field in which size effects have generally been ignored in practice. However, tests (12, 25, 50, 63–65) motivated by new interest in building large ship and aircraft parts almost entirely with polymer composites clearly indicate a strong size effect, unobservable on the normal laboratory scale. For notched specimens, or structures in which a large crack or damage zone develops before P _{max}, the type 2 sizeeffect law (Eq. 1) was shown to apply (63), but the expressions for D _{0} and σ_{0} are complicated by material orthotropy and irregular or starlike shape of a large FPZ. Compression failure due to fiber kinking (with microbuckling) also follows type 2 size effect law (Eq. 1) but with a modification: σ _{N} must be replaced by σ _{N} – σ _{r} , where σ _{r} = residual compressive stress across the propagating kink band, equal to about a half of the initial compression strength (25). This was deduced from the compressive cohesive crack model for kink band using perturbation analysis of the J integral for the energy flux into the FPZ of kink band and was verified by tests of size effect in compression failure of unidirectional carbon–epoxy and carbon–PEEK (polyetheretherketon) composites.
Fiberreinforced concretes and polymers with short fibers exhibit more complex size effects, different for two local peaks on the loaddeflection curve: one peak for matrix fracture and another for fracture and frictional pullout of fibers from the crack faces.
The size effect observed in flexural failure of laminates (66, 67) has long been attributed to pure Weibull statistical theory. The existing sizeeffect data alone can of course be fitted by that theory, but it has been neglected to check the corresponding CoV of strength, which would have to match Weibull theory but does not. Weibull moduli m obtained from sizeeffect data for various layups of the same prepregs vary immensely (from 4 to 40), but this corresponds to CoV = 23% and 4%, respectively, both of which are totally unrealistic, thus ruling out pure Weibull size effect (50). The mean sizeeffect data can be matched consistently with the type 1 sizeeffect law (Eq. 16), in which the statistical part is irrelevant (equal to 1) for normal situations (thickness < 5 cm) and can matter only for much thicker laminates.
Foams, Sandwich Structures, and Composite Beams. Vinyl foam typically used for sandwich plates is normally thought to be ductile (68), but tests and simulations reveal a strong type 2 sizeeffect if the foam has a notch or damaged zone (64, 69–71). So, size effect must naturally be expected in sandwich plates with foam core, as indicated by preliminary tests. However, the size effect is complicated by core indentation, skin wrinkling, and delamination buckling.
Hierarchical Size Effects in Composite Structures. In a large steel–concrete composite beam, the connectors do not fail simultaneously, as plastic limit analysis dictates, but in sequence, similar to a propagating crack. Of course, size effect ensues. But the pullout of the connectors themselves from concrete slab also exhibits a size effect, amplifying the first. The result is a size “super effect,” such that σ _{N} ∝ D ^{–3/4} for D → ∞ (12, 13, 72).
Ceramics, Rocks, and Masonry. Testing of ceramics (e.g., refs. 18 and 73) shows them to be quasibrittle and exhibit a size effect of type 1 or 2 but on a smaller scale (ℓ from 0.1 to 10 mm). The same applies to intact rocks (24, 74). ℓ and D _{0} are roughly proportional to the grain size (and can differ by as much as 100:1 between marble and breccia, e.g.). In rock masses, however, the dominant heterogeneity is not the grain size but the spacing of rock joints, typically ≈10 m. Accordingly, one must expect the characteristic length ℓ for size effect on the sliding of a mountain that consists of jointed rock to be of the order of 100 m. However, the rock excavation scale in normal construction is generally too small for significant size effect of this kind.
Masonry is also quasibrittle, with ℓ of the order of 1 m, which may help to explain the collapses of ancient massive towers in Italy, after about seven centuries of placid existence. The critical time is set by longterm drying of thick walls, causing shrinkage, which leads to compression failure of cladding, assisted by size effect (D. Ferretti and Z.P.B., unpublished results).
Breakout of Boreholes in Rock and Mining Excavations. The breakout of deep boreholes under remote compressive stress σ _{N} exhibits size effect as a function of borehole diameter D. There may be a residual stress σ _{r} , and it was shown that σ _{N} – σ _{r} asymptotically approaches either D ^{–1/2} or D ^{–2/5} (the anomalous exponent –2/5 arises if the spacing of axial splitting cracks around the borehole is not dictated by grain size but is free to minimize σ _{N} ) (75). The explosive breakout of mining stopes doubtlessly exhibits a similar size effect.
Triggering of Snow Avalanches and Landslides. Dry snowslab avalanches are triggered as mode II (shear) fractures in a weak layer at the slab base. The cohesive crack model leads to a type 2 size effect of slab thickness D but with a modification: the size effect depends on preexisting frictional stress in a weak layer and is offset by an effect of D (or snow weight) on fracture energy and residual shear stress. The theory correlates with hundreds of avalanche observations (21).
Structures with Finite Angle Notches. The power λ(γ) of the elastic stress singularity at finiteangle notches is known to decrease as the notch angle, 2γ, increases (76). However, P _{max} of a body with such a notch must be determined not from the singularity but from the analysis of a cohesive crack emanating from the notch tip. For γ → 0, the type 2 size effect must be approached: for γ → π, the type 2 size effect must disappear; and for D → ∞, Williams' (76) stress field must be approached for any γ. From these asymptotic conditions, one can deduce (by similar asymptotic matching as above) the sizeeffect formula where functions ψ(γ) and λ(γ) are taken from ref. 76. This formula agrees with finite element solutions for a cohesive crack emanating from the notch as well as with tests (38).
Fatigue, Rate Effect, and Dynamics. The classical Paris–Erdogan law for increments of crack length a per cycle, Δa/ΔN ∝ (CΔK_{I} ) ^{n} , requires a sizeeffect correction of C if the FPZ is not negligible (ΔK_{I} = amplitude of cyclic K_{I} , and n = constant of the order of 10). Based on Eq. 1, it was shown that C = (1 + D _{0}/D)^{–1/2} (9, 12, 13). Under monotonic or sustained loads, viscoelastic behavior of the material causes the FPZ to shorten, which makes the size effect and brittleness for slow or longtime loading greater than for fast or shorttime loading (77). For very fast loading, the size effect is significantly modified by rate dependence of the softening stressseparation law of cohesive cracks (77). In dynamics, any type of viscosity η _{v} implies a characteristic length, ℓ _{v} = η _{v} /vρ, and then t_{ch} = ℓ/v becomes a characteristic time for developing size effect (v = wave velocity and ρ = mass density).
SizeEffect Simulation with the Cohesive Crack Model. Finite element computations of size effect with the cohesive crack model used to require stepbystep computation of the entire loading process for each size (43). However, the sizeeffect curve can be computed directly after conversion to an eigenvalue problem (12, 13, 78, 79). One must reformulate the problem in dimensionless variables, choose a series of relative crack lengths α _{i} (i = 1, 2,...), and then search for size D for which the condition dσ _{N} /dα = 0 is satisfied. This leads in dimensionless coordinates to a homogeneous Fredholm integral equation with D as the first eigenvalue. The load P _{max} corresponding to each α _{i} can then be accurately evaluated after integrating the eigenvector.
SizeEffect Simulation by Crack Band, Nonlocal, and Discrete Models. The theoretical length of a fully developed FPZ, as well as its width, may in some applications be much larger than the structural crosssection size D. In that case, typical for concrete and geotechnical engineering and often composites as well, the FPZ volume needs to be subdivided by finite elements, and the constitutive model must capture gradual strain softening of the material due to distributed damage. However, in the absence of countermeasures, the structural tangent stiffness matrix of such a model is not positivedefinite. The result is ill conditioning of the boundary value problem, excessive strain localization into a set of measure zero, pathological zerodissipation failure, spurious mesh sensitivity, and false size effect. The proper countermeasure is some form of nonlocal continuum concept (80), involving a material characteristic length ℓ. This is achieved by the nonlocal concept of damage (81) and its diverse refinements (82) [including statistical (31)], in which the nonlocal inelastic strain (or its parameter) at a continuum point is averaged over a zone of a certain characteristic size equal roughly to the FPZ width.
Frequently for large structures, the FPZ width need not be subdivided into finite elements, and then the simplest approach is the crack band model (8, 10), now widely used in industry and specialized commercial software (sbeta, diana, and atena). In that model, the postpeak portion of the softening constitutive law is scaled according to the finite element width so as to ensure correct energy dissipation. For localizing deformation, both the crack band and nonlocal models are approximately equivalent to the cohesive crack model. The longstanding challenge of a realistic threedimensional constitutive model for softening damage in the FPZ has been met for concretelike composites with the microplane model (83, 84). A more realistic nonlocal model requires capturing the tensorial interactions of microcracks of various orientations, with their spatial decay, and distinguishing between the shielding and amplification zones of each microcrack (85). Even better is direct simulation of the coarse microstructure by a random particle or lattice model (86).
Stochastic Finite Element Methods (SFEMs). Computing loads with required failure probability p_{f} ≤ ≈10^{–7} is a challenge that cannot be met by the existing standard SFEMs, because they can capture only loworder statistical moments and not the faroff pdf tail. To meet this challenge, Weibull statistical size effect must ensue from SFEM for D → ∞ if the structure fails at crack initiation (32, 39). The existing standard SFEMs do not pass this check. As a remedy, the probabilistic theory of extreme values must be embedded in the SFEM in some way. This can be done by subdividing the structure into many domains scaled up with the structure size, in each of which the material strength limit is scaled down (according to the stability postulate of extreme value statistics) as a function of domain size (31).
Grim Example: Malpasset Dam. Collapse of this recordthin arch dam in 1959 flooded the town of Fréjus (founded by Caesar), killing almost 400 inhabitants. The identified direct cause (slipping of gneiss in abutment; Fig. 1s ) is undisputable; however, according to scaling law (Eq. 16), the tolerable displacement of abutment would today be 51% smaller than considered in design in 1951 (30) (and doubtless still smaller if the pdf tail at p_{f} ≈ 10^{–7} were properly taken into account). The scatter of energetic statistical size effect when the dam is scaled by various ratios is documented in Fig. 1t by computations of M. Vořechovský at Northwestern University (unpublished data) using a Weibulladapted crack band model (31). Their mean matches Eq. 16 perfectly. Because this law can be calibrated by deterministic computations alone, the use of SFEM, extremely demanding computationally, can be skipped in practice.
Challenge for Concrete Design Codes. With many thousands of different structures designed annually, structural engineering (unlike aeronautical engineering) is a field that cannot get by without a simple design code. However, codes are approved by broad society committees and thus are notoriously difficult to update. Nevertheless, the size effect, with probabilistically justified safety provisions, must eventually be introduced into all the code articles guarding against brittle failures of various types (numbering ≈20) (60).
Scaling of Metal Plasticity at a Micrometer Scale. Freestanding metallic thin films with a thickness of ≈1 μm exhibit under pure tension a strong size effect and stable strain softening similar to concrete on a meter scale (Z.P.B., Z. Guo, and H. Espinosa, unpublished data). The cause is that, on the face that was in contact with substrate, there exists an epitaxially induced boundary layer of much elevated yield strength, which acts in the manner of a type 1 size effect. Moreover, in bending, torsion, and indentation tests, the yield strength is increased due to geometrically necessary dislocations associated with plastic strain gradients. Asymptotic scaling analysis analogous to the present one points out a way to improve the straingradient theory (13, 87) and explains the effect of particle size in metal–matrix nanocomposites.
Closing Comments
Even if the size effect per se is not the analyst's objective, the knowledge of size effect, or scaling, helps in obtaining analytical failure predictions in general. For the actual size of interest, a direct analytical solution may be next to impossible. However, by scaling the structure down to a vanishing size or up to an infinite size, one gets a problem of plasticity or LEFM, each of which is much easier. Knowing these asymptotic solutions, an approximate analytical solution for the actual size can then be obtained by asymptotic matching. It is for this reason that the size effect is the key problem for all quasibrittle failures.
Fracture scaling often interacts with spatial, temporal, and thermal scaling of mass transport and chemical processes. An example is the modification of size effect due to shrinkage stresses and microcracking caused by drying of concrete (56), which evolves initially as a square root of both depth and time, and the halftime of which scales as structure thickness square. Processes of material deterioration include microfracturing due to expansion of reacting particles of various sizes (e.g., alkalisilica reaction or sulphate attack in cements). Typically, particle reactivity goes up when the particle size decreases, but this is offset by the fact that the particle pressure required to fracture the matrix increases (88). Such phenomena, however, are beyond the scope of this overview, and so are the polemics on a possible role of crack fractality (20).
Further opportunities abound. One is bone, the microstructure of which is sure to cause quasibrittle behavior. Hardly explored from the present viewpoint are biological shells, wood, paper, particle board, stiff clays, silts, coal, superstrength alloys, and most materials on approach to nanoscale. It is doubtless much fertile ground lies beyond our horizon.
Acknowledgments
This work was supported by Office of Naval Research Grant N0001402I0622 to Northwestern University.
Footnotes

↵ * Email: zbazant{at}northwestern.edu.

This contribution is part of the special series of Inaugural Articles by members of the National Academy of Sciences elected on April 30, 2002.

Abbreviations: FPZ, fracture process zone; LEFM, linear elastic fracture mechanics; pdf, probability density function; CoV, coefficient of variation; SFEM, stochastic finite element method.

See accompanying Biography on page 13397.
 Copyright © 2004, The National Academy of Sciences
References

↵
Galileo, G. L. (1638) Discorsi i Demostrazioni Matematiche Intorno à due Nuove Scienze (Elsevirii, Leiden, The Netherlands).

↵
Mariotte, E. (1686) Traité du Mouvement des Eaux: Mariotte's Collected Works (The Hague, The Netherlands), 2nd Ed. (French)

↵
Weibull, W. (1939) Ingenioersvetenskapsakad. Handl. 153 , 1–55.
 ↵

↵
Weibull, W. (1949) Proc. R. Inst. Technol. 27 , 1–55.

↵
Freudenthal, A. M. & Gumbell, E. J. (1956) in Advances in Applied Mechanics (Academic, New York), Vol. 4, pp. 117–157.

↵
Walsh, P. F. (1972) Indian Concr. J. 46 , 469–470, 476.

↵
Bažant, Z. P. (1976) J. Eng. Mech. Div. Am. Soc. Civil Eng. 102 , 331–344.

↵
Bažant, Z. P. & Planas, J. (1998) Fracture and Size Effect in Concrete and Other Quasibrittle Materials (CRC, Boca Raton, FL).

↵
Bažant, Z. P. & Oh, B.H. (1983) Mater. Struct. 16 , 155–177.

ACI Committee 446 (1992) in Fracture Mechanics of Concrete Structures, ed. Bažant, Z. P. (Elsevier, London), 1–140.

↵
Bažant, Z. P. (2002) Scaling of Structural Strength (Hermes Penton Science, London), 2nd Ed.

↵
Bažant, Z. P. (2004) Introduction aux Effects d'Échelle à la Résistence des Structures (Hermes, Paris).

↵
Bažant, Z. P. (1984) J. Eng. Mech. 110 , 518–535.
 ↵

RILEM Committee QFS (2004) Mater. Struct. 47 , in press.

↵
Bažant, Z. P. & Chen, E.P. (1997) Appl. Mech. Rev. 50 , 593–627.

↵
Bažant, Z. P. & Kazemi, M. T. (1990) J. Am. Ceram. Soc. 73 , 1841–1853.

↵
Bažant, Z. P. & Yavari, A. (2004) Eng. Fract. Mech. 43 , in press.

↵
Bažant, Z. P., Zi, G. & McClung, D. (2003) J. Geophys. Res. Solid Earth Planets 108 , 2119–2129.

↵
Dempsey, J. P., Adamson, R. M. & Mulmule, S. V. (1999) Int. J. Fract. 95 , 346–378.

↵
Gettu, R., Bažant, Z. P. & Karr, M. E. (1990) ACI Mater. J. 87 , 608–618.

↵
Bažant, Z. P. & Kazemi, M. T. (1990) Int. J. Fract. 44 , 111–131.
 ↵

↵
Bažant, Z. P. & Li, Z. (1995) J. Struct. Eng. 121 , 739–746.

↵
Bažant, Z. P. & Li, Z. (1996) J. Eng. Mech. 122 , 458–468.

↵
Bažant, Z. P. (1998) in Fracture Mechanics of Concrete Structures (Proc., FraMCoS3), eds. Mihashi, H. & Rokugo, K. (Aedificatio, Freiburg, Germany), pp. 1905–1922.

↵
Bažant, Z. P. & Novák, D. (2000) J. Eng. Mech. 126 , 166–174.

↵
Bažant, Z. P. & Novák, D. (2000) ACI Mater. J. 97 , 381–392.

↵
Bažant, Z. P., Pang, S.D., Vořechovský, M. & Novák, D. (2004) Proceedings of the Fifth International Conference on Fracture Mechanics of Concrete Structures (FraMCoS5), eds. Li, V. C., Leung, K. Y., Willam, K. J. & Billington, S. L. (Intern. Assoc. of Fracture Mechanics of Concrete Structures, Evanston, IL), pp. 189–196.

↵
Bažant, Z. P. (2001) Proceedings of the Eighth International Conference on Structural Safety and Reliability (ICOSSAR), eds. Corotis, R. B., Schueller, G. I. & Shinozuka, M. (Swets and Zeitinger, Balkema, Lisse, The Netherlands), pp. 1–23.

↵
Barenblatt, G. I. (1996) Scaling, Selfsimilarity and Intermediate Asymptotics (Cambridge Univ. Press, Cambridge, U.K.).

↵
Barenblatt, G. I. (2003) Scaling (Cambridge Univ. Press, Cambridge, U.K.).

Bender, M. C. & Orszag, S. A. (1978) Advanced Mathematical Methods for Scientists and Engineers (McGraw–Hill, New York).

↵
Hinch, E. J. (1991) Perturbation Methods (Cambridge Univ. Press, Cambridge, U.K.).

↵
Bažant, Z. P. (2001) in Fracture Mechanics of Concrete Structures (FraMCoS4), eds. de Borst, R., Mazars, J., PijandierCabot, G. & van Mier, J. G. M. (Swets & Zeitlinger, Balkema, Lisse, The Netherlands), pp. 651–658.

↵
Bažant, Z. P. & Yu, Q. (2004) Proceedings of the Fifth International Conference on Fracture Mechanics of Concrete Structures (FraMCoS5), eds. Li, V. C., Leung, K. Y., Willam, K. J. & Billington, S. L. (Intern. Assoc. of Fracture Mechanics of Concrete Structures, Evanston, IL), pp. 153–162.

↵
Bažant, Z. P. (2004) Probab. Eng. Mech. 19 , in press.

↵
Barenblatt, G. I. (1959) Prikl. Mat. Mekh. 23 , 434–444.

↵
Rice, J. R. (1968) in Fracture: An Advanced Treatise, ed. Liebowitz, H. (Academic, New York), Vol. 2, pp. 191–308.

Palmer, A. C. & Rice, J. R. (1973) Proc. R. Soc. London Ser. A 332 , 527–548.
 ↵

↵
Hillerborg, A. (1985) Mater. Struct. 18 , 291–296.
 ↵

↵
Bažant, Z. P. & Xi, Y. (1991) J. Eng. Mech. 117 , 2623–2640.

↵
Irwin, G. R. (1958) in Handbuch der Physik, ed. Flügge, W. (Springer, Berlin), Vol. VI, pp. 551–590.
 ↵
 ↵
 ↵

↵
Bažant, Z. P. & Pfeiffer, P. A. (1987) ACI Mater. J. 84 , 463–480.

↵
Daniels, H. E. (1945) Proc. R. Soc. London Ser. A 183 , 405–435.

↵
Phoenix, S. L. & Beyerlein, I. J. (2000) Phys. Rev. E Stat. Phys. Plasmas Fluids Relat. Interdiscip. Top. 62 , 1622–1645.
 ↵

↵
RILEM (1990) Mater. Struct. 23 , 461–465.

↵
Planas, J. & Elices, M. (1992) in Fracture Mechanics of Concrete Structures, ed. Bažant, Z. P. (Elsevier, London), pp. 939–950.
 ↵

↵
Brocca, M. & Bažant, Z. P. (2001) J. Struct. Eng. 127 , 1382–1390.

↵
Burtscher, S. L. & Kolleger, J. (2004) Proceedings of the Fifth International Conference on Fracture Mechanics of Concrete Structures (FraMCoS5), eds. Li, V. C., Leung, K. Y., Willam, K. J. & Billington, S. L. (Intern. Assoc. of Fracture Mechanics of Concrete Structures, Evanston, IL), pp. 173–180.

↵
Bažant, Z. P. & Yu, Q. (2004) J. Struct. Eng., in press.
 ↵

↵
Bažant, Z. P. (1992) J. Geophys. Res. Oceans 97 , 17739–17751.

↵
Bažant, Z. P., Daniel, I. M. & Li, Z. (1996) J. Eng. Mater. Technol. 118 , 317–324.
 ↵

↵
Wisnom, M. R. (1992) J. Composite Mater. 26 , 1173–1180.

↵
Jackson, K. E. (1992) AIAA J. 30 , 2099–2105.

↵
Johnson, D. P., Morton, J., Kellas, S. & Jackson, K. E. (2000) AIAA J. 38 , 1047–1054.

↵
Gibson, L. J. & Ashby, M. F. (1997) Cellular Solids: Structure and Properties (Cambridge Univ. Press, Cambridge, U.K.), 2nd Ed.
 ↵
 ↵
 ↵

↵
McKinney, K. R. & Rice, R. W. (1981) in Fracture Mechanics Testing Methods for Ceramics, Rock and Concrete, eds. Freiman, S. W. & Fuller, R. W. (Am. Soc. Testing Materials, Philadelphia), pp. 118–126.

↵
Carter, B. C. (1992) Rock Mech. Rock Eng. 25 , 167–186.

↵
Bažant, Z. P., Lin, F.B. & Lippmann, H. (1993) Int. J. Num. Anal. Methods Geomech. 17 , 1–14.

↵
Williams, M. L. (1952) J. Appl. Mech. 74 , 526–528.
 ↵
 ↵

↵
Bažant, Z. P. & Li, Y.N. (1995) J. Appl. Mech. 62 , 959–964.

↵
Bažant, Z. P., Belytschko, T. B. & Chang, T.P. (1984) J. Eng. Mech. 110 , 1666–1692.

↵
PijaudierCabot, G. & Bažant, Z. P. (1987) J. Eng. Mech. 113 , 1512–1533.
 ↵

↵
Bažant, Z. P., Caner, F. C., Carol, I., Adley, M. D. & Akers, S. A. (2000) J. Eng. Mech. 126 , 944–953.

↵
Bažant, Z. P. & Caner, F. C. (2004) J. Eng. Mech. 130 , in press.

↵
Bažant, Z. P. (1994) J. Eng. Mech. 120 , 593–617.
 ↵
 ↵

↵
Bažant, Z. P., Zi, G. & Meyer, C. (2000) J. Eng. Mech. 126 , 226–232.
Citation Manager Formats
More Articles of This Classification
Physical Sciences
Related Content
Cited by...
 Mechanical resilience and cementitious processes in Imperial Roman architectural mortar
 (Finite) statistical size effects on compressive strength
 Scaling of strength and lifetime probability distributions of quasibrittle structures based on atomistic fracture mechanics
 Unified model of tectonics and heat transport in a frigid Enceladus
 Biography of Zdenek P. Bazant