## New Research In

### Physical Sciences

### Social Sciences

#### Featured Portals

#### Articles by Topic

### Biological Sciences

#### Featured Portals

#### Articles by Topic

- Agricultural Sciences
- Anthropology
- Applied Biological Sciences
- Biochemistry
- Biophysics and Computational Biology
- Cell Biology
- Developmental Biology
- Ecology
- Environmental Sciences
- Evolution
- Genetics
- Immunology and Inflammation
- Medical Sciences
- Microbiology
- Neuroscience
- Pharmacology
- Physiology
- Plant Biology
- Population Biology
- Psychological and Cognitive Sciences
- Sustainability Science
- Systems Biology

# Algorithmic lattice kirigami: A route to pluripotent materials

Edited by Sharon C. Glotzer, University of Michigan, Ann Arbor, MI, and approved April 30, 2015 (received for review March 26, 2015)

## Significance

How can flat surfaces be transformed into useful three-dimensional structures? Recent research on origami techniques has led to algorithmic solutions to the inverse design problem of prescribing a set of folds to form a desired target surface. The fold patterns generated are often very complex and so require a convoluted series of deformations from the flat to the folded state, making it difficult to implement these designs in self-assembling systems. We propose a design paradigm that employs lattice-based kirigami elements, combining the folding of origami with cutting and regluing techniques. We demonstrate that this leads to a pluripotent design in which a single kirigami pattern can be robustly manipulated into a variety of three-dimensional shapes.

## Abstract

We use a regular arrangement of kirigami elements to demonstrate an inverse design paradigm for folding a flat surface into complex target configurations. We first present a scheme using arrays of disclination defect pairs on the dual to the honeycomb lattice; by arranging these defect pairs properly with respect to each other and choosing an appropriate fold pattern a target stepped surface can be designed. We then present a more general method that specifies a fixed lattice of kirigami cuts to be performed on a flat sheet. This single pluripotent lattice of cuts permits a wide variety of target surfaces to be programmed into the sheet by varying the folding directions.

Reduced-dimensionality objects can be light yet extremely strong, as in a geodesic dome or the skeleton of a diatom (1). Design of such structures couples scale-independent geometry and topology with material properties to create a variety of structures. In soft gel sheets, programmed inhomogeneous swelling and stretching can generate tunable 3D shapes that can potentially serve as compliant mechanisms (2). In more rigid systems, origami applies a prescribed sequence of folds to a flat sheet and returns a strong, lightweight, and flexible 3D structure. A great deal of effort has gone into exploring the breadth of attainable origami surfaces starting from nearly unstretchable sheets (3⇓–5), including recent work on designing mechanical metamaterials (6) and self-folding origami structures (7).

In origami, the inverse problem of prescribing a set of folds to achieve a target structure has been algorithmically solved. For instance, the circle/river packing method can be used to create a 2D base for the final product which is then augmented with extra folds into the desired 3D shape (8). A different method wraps the initial flat sheet onto a polygonally tiled target surface, using tucking molecules to hide the excess material within the final shape, and thus creates curvature (9). Further, software has been developed by the same author to form developable, irregularly corrugated target configurations by modifying miura-ori–style patterns (10).

There are, nevertheless, certain limits and constraints in the use of origami to design generic structures. These problems center around the potential complexity of the initial fold pattern and the subsequent greatly magnified complexity of the required sequence of folds along this pattern. For instance, the fold patterns specified by the circle/river packing algorithms return a pattern whose folded state matches a target surface, but there is no guarantee that any subset of creases can be folded; complex models of this type are typically precreased and then folded in a very specific and repetitive sequence. The polygonally tiled surfaces created by the tucking molecule method are the product of intricately interlocking crimp folds hidden away beneath the surface. Both of these features reflect the fact that typically complex origami designs do not permit a monotonic, continuous folding motion from the planar state to the desired target state. These extremely delicate fold patterns present an obvious challenge to the goal of designing self-assembling origami structures, where in many cases extremely fine control of the fold ordering may be required. Additionally, these fold patterns often waste much of the surface to create effective areas of Gaussian curvature, using extremely intricate folds, wedges, and pleats to effectively remove material, hiding it beneath the visible surface.

Recently, we introduced lattice kirigami methods to this design problem (11); inspired by the work of Sadoc, Rivier, and Charvolin on phyllotaxis (12⇓–14), we supplemented the folds of origami with a limited set of cutting and regluing moves taking place on a honeycomb lattice (11). The essence of our kirigami constructions is that after making the prescribed cuts and identifying edges we have a surface with localized points of Gaussian curvature, which cause the surface to buckle into a 3D configuration. Associated folding then precisely defines the shape of the surface, corralling the points of Gaussian curvature into useful cues that direct the shape of the final structure.

The restrictions imposed on kirigami by the honeycomb lattice and its triangular dual lattice led to a manageable set of allowed motifs: 2–4 disclination pairs on the honeycomb lattice and *A*, where the vertices of the cut pattern are seen to lie on the dual lattice sites. In contrast, the vertices of the cut pattern for 2–4 pairs lie entirely on the honeycomb lattice and its basis; thus, in its folded configuration a 2–4 defect pair will appear as a pair of neighboring points on the honeycomb lattices with twofold and fourfold coordination (instead of the normal threefold). Another allowed kirigami motif is the sixon, a defect formed by completely removing one hexagon from the honeycomb lattice and reconnecting the cut edges of the remaining surface in one of several degenerate ways. One configuration of the sixon identifies pairs of adjacent edges so that three triangular plateaus emanate from a central point; another configuration leads to matching 2–4 pairs in a pop-up/pop-down configuration (11).

In this paper we show that arrangements of these kirigami motifs enables a remarkably versatile ability to design patterns whose cut-and-folded state matches a desired target surface, allowing us to algorithmically solve the inverse design problem for a particular class of surfaces with a specified maximum gradient.

Importantly for their potential for self-assembly, the kirigami design paradigms we propose are both simple—to the extent of being easily designed by hand—and robust to the ordering and relative rates of edge folding. In what follows we will first describe a simple solution to the inverse design problem of creating a stepped surface with assigned heights at each point by arranging paired

## Design Using 5 ˜ –7 ˜ Elements

Fig. 1 depicts a single

A workable design paradigm requires combining many of these kirigami elements together, and in general one of the challenges of kirigami design is to understand the allowed relative configurations of kirigami elements. Important progress can be made by realizing that a collection of

Fig. 2 *A*–*E*, *Left*, demonstrates the allowable ways (modulo rotations in *Middle*, shows the folded configuration of each of these basic building blocks. In our nomenclature, “Unit *n*” refers to a superlattice hexagon with *n* of its sides replaced with a *F* labeled “special units” contain points at which three dislocations, whose Burgers vectors sum to zero, have positive-climb paths that converge together (as described in the Supplementary Material in ref. 11). In real materials these special units may be less stable than the other units, but their use substantially simplifies the design of target structures.

Fig. 2, *Right*, shows a simplified 2D representation of each structure given by color-coding the edges of the hexagonal superlattice as either folds or cuts (trivially done by comparing the relative elevation of the structure across a line). The allowable configurations can be determined by considering each vertex of the superlattice, as shown in Fig. 2*G*: to avoid tearing and other unwanted structural deformations of the sheet, each vertex must have either zero or two folding lines incident upon it.

With this junction rule in hand it is straightforward to reverse engineer a 2D map of the *Supporting Information* we demonstrate this by designing a kirigami ziggurat, which we then realize in a simple experimental setting.

However, even aside from the restrictions imposed by the junction rules described above, these

## Deploying Sixons for Surface Design

As before, to make use of the sixon structure we must understand the allowed arrangements of sixons with respect to each other. Fortunately, this is particularly straightforward: multiple sixons can be arranged in a triangular lattice. That is, the fold patterns required by the placement of multiple sixons can be made commensurate by choosing the excised hexagon centers to lie on a triangular lattice. The simplest implementation of this is shown in Fig. 3*A*. The folded state of this pattern, schematically shown in Fig. 3*B*, consists of triangular basins at height 0 separated by triangular plateaus at height 1 (in units of the sidewall heights). By thinking of this structure in a gravitational potential we consider the configuration in Fig. 3*B* to be the ground state of the triangular lattice of sixons because it minimizes the sum of the relative plateau heights.

Local excitations of this configuration correspond to changing the plateau heights, for instance, by interchanging the nested valley and mountain folds around a height-zero triangular basin, creating a height-two triangular plateau surrounded by height-one plateaus. If the sheet can bend and stretch as in bistable origami (17), transforming from the ground state to these excited states only requires opening and then reclosing the three excised hexagons that bound the relevant triangular plateau. Otherwise, to avoid tearing or bending while moving from one target to another, it is necessary to return to the completely flat state. The requirements that folds be commensurate and the sheet not stretch impose the only restriction on allowed excitations: the height of any triangle in the folded configuration must differ by one from the height of any triangle with which it shares an edge. One such excited state is shown in Fig. 3*C*; as shown in Fig. 3*D*, given a reduced representation of the heights, it is trivial to assign the corresponding mountain and valley folds in the real sheet.

The restriction on the excited states is quite modest, making it easy to design a cut-and-fold pattern based on a triangular lattice of sixons that approximately matches a target surface with a stepped surface of triangular plateaus. In this formulation, achievable target surfaces are limited only to have a maximum gradient set by the ratio of plateau height to plateau width. If the gradient of the target surface obeys this bound, finding the kirigami solution to the inverse design problem is as straightforward as projecting the heights of a target surface down onto a triangular lattice and then rounding the height assignment of each triangle to the nearest even or odd integer so that triangles sharing an edge will have heights that differ by exactly one. Indeed, if there is a known maximum gradient among the target surfaces into which a sixon array will be (re)configured, the cut sizes determining the ratio of plateau height to width can be chosen to match this maximum gradient. From the triangular height map the pattern of mountain and valley folds immediately follows, as in Fig. 3*D*. We illustrate this simple design paradigm in Fig. 4, where the same triangular lattice of sixons can be used to approximate (to pick two arbitrary examples) both a monkey saddle and the topographic features at the northern terminus of the US Appalachian Trail (18).

## Conclusion

We have demonstrated that adding kirigami cutting motifs to the folds of origami leads to a powerful framework in which target structures can be algorithmically designed via arrays of kirigami elements. Subject to a gradient constraint, using a superlattice simplifies the design for a static target surface, whereas triangular lattices of sixons form a versatile base pattern able to accommodate fold patterns for any stepped target structure. If the material allows for dynamic changing of fold type, then the sixon lattice can be reconfigured between arbitrary surface configurations. Current studies involve designing pluripotent kirigami templates that lift the gradient limitation as well as other geometric and topological limits. We note that our choice of triangular plateaus and sixons was a powerful but not entirely unique choice with which to engineer a pluripotent sheet of kirigami elements. We show in *Supporting Information* that using square plateaus leads to a similar (but more restrictive) design paradigm.

We note that our kirigami designs are superior to many origami designs for comparable results, especially in relation to self-assembly. For example, our experimental realization of a ziggurat-style pryamid (*Supporting Information*)—actuated by heat-shrink tape placed across the short axis of the excised hexagons—makes it clear that in our kirigami constructions the fold process is very robust. That is, in contrast with the origami methods discussed above, detailed control over the folds is not necessary to correctly form the target structure. Also, unlike some origami designs, this kirigami-based approach to approximating surfaces with sixons maintains a constant complexity of fold pattern per unit surface area. The underlying structure is always a triangular lattice of sixons, and different surfaces differ in their folding template only by switching mountain and valley folds as needed.

Because the folds connecting sixons are coupled, a triangular lattice of sixons has more fold lines than degrees of freedom. This attribute could be exploited to create truly multipotent kirigami sheets by partitioning the folds into nonoverlapping sets and programming each of those sets to fold in response to different stimuli. We schematically illustrate such a duopotent sheet in *Supporting Information*, programming half of the fold lines to form a half-cylinder when activated, whereas the other half of the fold lines transform the sheet into a Mexican hat potential. This raises the exciting prospect that with dynamical control over the fold type, a single lattice of sixons could serve as the base for, e.g., microfluidic devices with dynamically changeable channels. Work on implementing such a dynamically reconfigurable kirigami surface is currently underway. We also anticipate that exploring the collective elasticity of these kirigami sheets will provide further insight into 2D mechanical metamaterials (19).

In the first section we comment on actively controlling subsets of folds to make a duopotent sixon sheet. In the second section we provide additional details of our

## Pluripotent Sixons

As described in the main text, a triangular lattice of sixons has the potential to fold to any target conformation that satisfies the maximum-gradient constraint. Once the hexagons are excised, it is the fold lines between these hexagons that will then determine the final conformation. If the folds could be dynamically reprogrammed—certainly possible using electrically actuated hinges and perhaps with other implementations as well—then the surface could transition between different configurations of the dynamically pluripotent sheet, using the flat configuration as an intermediate state.

In practice, depending on the method used, it may be difficult to implement complete dynamic control over every fold in a lattice of sixons. Nevertheless, there are more fold lines than degrees of freedom in a sixon lattice, and this fact can be exploited to create multipotent kirigami sheets. The idea is to preprogram subsets of fold lines to bend in particular directions; given that there are more folds than degrees of freedom, one can completely specify multiple target surfaces by patterning multiple such subsets to actuate in response to different external stimuli. This works even if one is limited to actuating each fold line only in response to one of the external stimuli, i.e., using disjoint subsets of folds to control target structures.

A robust implementation of this is schematically shown in the duopotent sheet in Fig. S1, which exploits the fact that around every triangular plateau are two concentric folding-line triangles. Controlling, e.g., all of the fold lines surrounding the upward facing triangles guarantees that the complementary folds automatically complete as the surface moves from the flat state to the target configuration with all of the holes closed. In this way, programming the upward facing triangles specifies one target surface, whereas programming the downward facing triangles specifies a second independent target surface. In Fig. S1 we have illustrated this idea by programming the folds of one set of triangles to produce a half-cylinder, whereas the other triangles define the beginnings of a Mexican hat potential. It is our hope that such combined configurations can be used by experimentalists to verify the utility of the sixon lattice as a reconfigurable medium by using different stimuli to activate each set of folds.

## The 5 ˜ –7 ˜ Kirigami Design

### Design Rules.

In the main text we showed that the basic units for this method of kirigami design are

Within this framework, the height difference between adjacent hexagons cannot be larger than one step (the height of the vertical side walls), and each hexagon must have at least one adjacent hexagon at a different height. These constraints set the ultimate resolution that we are able to achieve with these designs. The junction rules also impose some minor nonlocal restrictions on the allowed combination of kirigami units, and depending on the complexity of the target surface, the initial projection of heights may have to be modified to satisfy these constraints. Nevertheless, target surfaces that do not violate the above restrictions can be designed by joining basic kirigami units together. As a proof of concept, we choose a pyramidal target surface. As illustrated in Fig. S2, we first project the height of the pyramidal surface onto the superlattice. The junction rules illustrated by the height projection are then easily turned into a cut-and-fold pattern, and the final state of this pattern is then rendered.

### Experimental Realization.

To complement our schematic designs in the main text and above, we demonstrate a particularly simple experimental setting in which our kirigami design principles can be implemented. We used Tyvek (nonwoven, Spunbonded Olefin, Type 10) as our 2D material because it is stronger and more tear-resistant than standard paper. We cut the pattern in Fig. S2*C* onto the Tyvek and precreased the folds. We then taped heat-shrinkable polyolefin (3M) underneath the hexagonal cuts and baked at 95°C for 3 min. By using polyolefin strips whose width was double that of the hexagonal cut (the shrinking ratio of the polyolefin is 2:1) the hexagonal gaps were completely closed during the baking step, and the Tyvek was folded into the target structure shown in Fig. S3. With the folds precreased this method led to sharper steps in the folded state compared with applying the polyolefin directly to the fold lines. This autonomous self-assembly of our 3D target structures demonstrates the robustness of our kirigami rules.

## Square Cut Design

Our choice of a honeycomb lattice in the main text and above on which to base our kirigami designs is far from unique. Different lattices have different concomitant angles and will thus generate kirigami surfaces with differently shaped tiles. One obvious alternative to the hexagonal lattice is the square lattice, and modifying the sixon technique in the natural way generates a kirigami surface with square tiles. Fig. S4 shows the basic unit of square lattice kirigami: the portion enclosed by dotted lines tiles space, the white central squares are excised, the red squares at the corners become the square plateaus, and the gray squares become the vertical side walls. In this formulation the sidewall height is set to be the same as the plateau width; to independently vary the plateau size and sidewall heights, the plateaus and excised squares remain square but change in relative size, whereas the sidewalls become rectangular.

Fig. S5 shows the two symmetrically distinct configurations formed by identifying the edges of the excised square in different ways. A desired target structure can then be designed by stitching these units together, just as in the

## Acknowledgments

Y.C. thanks Prof. D. J. Srolovitz for stimulating discussions and comments. The authors acknowledge support from National Science Foundation Emerging Frontiers in Research and Innovation - Origami Design for Integration of Self-assembling Systems for Engineering Innovation (NSF EFRI-ODISSEI) Grant EFRI 13-31583. D.M.S. was supported by the Advanced Materials Fellowship from the American Philosophical Society. This work was partially supported by a Simons Investigator Grant from the Simons Foundation (to R.D.K.).

## Footnotes

↵

^{1}D.M.S. and Y.C. contributed equally to this work.- ↵
^{2}To whom correspondence should be addressed. Email: kamien{at}physics.upenn.edu.

Author contributions: D.M.S., Y.C., T.C., X.G., S.Y., and R.D.K. designed research; D.M.S., Y.C., T.C., X.G., E.J., and R.D.K. performed research; E.J. analyzed data; and D.M.S., Y.C., T.C., S.Y., and R.D.K. wrote the paper.

The authors declare no conflict of interest.

This article is a PNAS Direct Submission.

This article contains supporting information online at www.pnas.org/lookup/suppl/doi:10.1073/pnas.1506048112/-/DCSupplemental.

## References

- ↵
- ↵.
- Klein Y,
- Efrati E,
- Sharon E

- ↵.
- Miura K

*Proceedings of the 31st Congress of the International Astronautical Federation, IAF-80-A 31*(Am Inst Aeronaut Astronaut, New York), pp 1–10 - ↵.
- Mahadevan L,
- Rica S

- ↵.
- Borrelli V,
- Jabrane S,
- Lazarus F,
- Thibert B

- ↵.
- Silverberg JL, et al.

- ↵
- ↵.
- Lang RJ

*Proceedings of the Twelfth Annual Symposium on Computational Geometry*(Assoc Comput Mach, New York), pp 98–105 - ↵.
- Tachi T

*Origami4*(CRC Press, Taylor & Francis Group, Boca Raton, FL), pp 259–272 - ↵.
- Tachi T

- ↵
- ↵
- ↵
- ↵
- ↵
- ↵.
- Benbernou NM,
- Demaine ED,
- Demaine ML,
- Ovadya A

- ↵
- ↵US Geological Survey (1999) Elevation data set n46w069sm (US Department of the Interior, Washington, DC).
- ↵

## Citation Manager Formats

## Sign up for Article Alerts

## Jump to section

## You May Also be Interested in

_{2}conditions, by the late 21st century, increasing temperatures could lead to reduced snowpack, drier summers, and increased fire risk, independent of changes in winter precipitation.

### More Articles of This Classification

### Physical Sciences

### Related Content

- No related articles found.